Download aircraft model drawings. Craft airplane - how to make a model airplane from wood, paper and plastic with your own hands. Equipment for launching gliders

It is considered one of the easiest to fly, therefore it is suitable for a beginning model pilot and can be used as a trainer, that is, as a first model for flight training.

To make a model airplane you need the following materials:
Smooth ceiling tiles or laminate backing, 3-5 mm thick.
Glue for the ceiling, this is Titan or any of its analogues, a disposable syringe of 5-10 ml.
Scotch tape of different colors, glue for paper.
A piece of thin but stiff wire, for example a piano string, wire for a semi-automatic welding machine, diameter D = 0.8-1 mm.
A flat base for working with a knife, for example a sheet of plexiglass, a laminate board.

Required parts:
Receiver and transmitter for 4 commands or more.
Electric motor for aircraft at 1100 rpm or more.
Servos 5-9 grams 4 pcs.
12 volt LiPo battery 1000-2000 mAh. 1 PC.
Propeller size 8040-9060.

Required tools:
Modeler's knife or stationery knife with spare blades.
Metal ruler 50-100 cm.
Sandpaper, emery block (stone).

Point 1. Preparation for work.
First you need to find it on the Internet, or take it here ( (downloads: 4684)) drawings of the aircraft model itself, then print them on a printer in A4 sheet format.

Lay out the resulting printouts on a flat surface in accordance with serial numbers, the result should be a connected image of the finished elements of the aircraft.

Now you need to glue the necessary sheets together. For proper gluing of sheets, so as not to disturb the dimensions and geometry of the future aircraft, it is necessary to cut off the excess edges on each sheet of the drawing, for the convenience of determining the cutting lines, special border crosses are drawn at the corners, all that remains is to decide which side we will cut, connect the two corner crosses with a line and get cutting line.

After removing the excess sides with scissors, we connect the resulting fragments of the drawing together, evaluate how well everything fits together, after which you can apply glue to the uncut edges of the sheet and glue it together.

The joints must match very precisely.

In this way we glue together all the fragmented elements of the drawing. The result should be seven glued and two single sheets (for the Cessna182 drawing).

Point 2. Cutting blanks.

Now you can lay out a “sandwich” from the backing and the drawing. To make it easier to hold the sheet on the backing, you just need to glue it a little with a pencil. During further manipulations, it will not have time to dry completely and therefore the paper (stencil) from the finished part will be easily removed without being damaged at all for reuse.

Then you can do it in different ways, depending on who you like best.

If the part is simple, with big amount straight lines, then it is enough to mark all the corners of the part with needle punctures, then remove the stencil paper and, applying a ruler from the puncture point to another point, make a cut with the tip of a knife, then move the ruler to the next points and so on until you complete cutting out the part completely.

If the part has a complex shape, with rounded sides, then you can immediately cut using a stencil and completely cut out the workpiece.

In this way, all the parts of the aircraft model are cut out. If you are making your first model, then you need to lay out or mark each of the parts so that you can easily determine its purpose from the drawing.

Point 3. Gluing the aircraft body, assembly.
You can start by gluing double partitions, that is, consisting of several identical parts glued together for additional strength.
Like this fuselage partition, for example.

We will use Titanium glue, as it is the most accessible for most beginning modelers, and to apply glue it is convenient to use a syringe without a needle, fill it with glue and use it as a convenient dispenser.

The cut parts are not always smooth enough; this can be easily corrected with sandpaper.

Now we take one side of the fuselage and place it with the correct side on the table so that the laminated side is on the outside of the aircraft. We cut out all the docking and mounting holes in the sidewall, then we put the second half and copy the same holes onto it.

We take the front partition of the compartment, apply glue to the glued side of the workpiece and press it into its installation location, move the workpiece a little in different directions so that the glue is well smeared and again separate the workpieces for 10-30 seconds to dry the glue. (to speed up, you can wave or blow), then connect the parts again and press with force for 5-10 seconds.

Now you can let go and work on other workpieces, periodically checking how the first workpiece is glued and, if necessary, pressing it further.

During the process of building an aircraft, it is important to timely monitor such things as the size of your battery (it may be larger than planned in the drawing) and accordingly independently adjust the dimensions of the compartment if necessary, constantly check the perpendicularity of the parts being glued, do this with a square or ruler.

This is how all the partitions of the front, middle and rear parts of the fuselage are assembled in stages.

When all the partitions are installed, you can glue the second side of the fuselage.

We are finishing the face and mounting for the motor mount.

We install the upper part of the fuselage with a slot for the tail (rudder).

We glue the tail blanks together, immediately lay in reinforced tape reinforcement for attaching the rudder and toothpicks for rigidity.

We clamp the gluing with a board and clamps for even gluing.

As a result, everything is smooth and toothpicks do not stand out.

Glue the tail into place.

We always check and maintain a strict vertical line.

We glue together the parts of the elevator, we also put a bamboo skewer and tape inside for attaching the steering wheel, we perforate the tape with holes for better gluing of the ceiling halves.

We also compress it with a board and clamps until the glue dries completely, about a day.
We grind the edges at an angle of 45 degrees so that when the planes are tilted they do not rest against each other; this is convenient to do with a simple stone block or sandpaper.

We make a wing, mark lines on the wing for gluing stiffeners, ribs, spars.

The wooden axis (spar) is usually made from a 50 cm wooden ruler; if you have a circular saw, you can simply spread the board onto the shingles and then cut it to the required size.

First we glue the spar rail.

We reinforce the joint in the middle with two more small slats.

Then we glue in the foam neurites.

To glue the upper plane of the wing, the ceiling or substrate material must be prepared, rolled on a piece of pipe to set a preliminary bend of the desired shape, after which glue can be applied to all contacting elements and the final gluing can be performed. To fix the wing while the glue sets, you can use any of the available weights, clothespins, or tape.

Small dents in the field of clothespins can be sanded with sandpaper.

In the central part of the wing we close the cavities and glue in the inserts.

After the glue has completely dried, we mark the ailerons, additionally focusing on the clearance so as not to get on the partition.

We cut through with a cutter on both sides and take out the finished aileron.

We seal all opened cavities with strips of tiles.

The finished ailerons can be glued immediately using reinforced tape or left for later, until the entire model is covered with tape.

The front of the wing can also be reinforced with reinforced tape.

Now you can cover the entire model with tape, this is not only for beauty, but mostly to give it strength; now the model will be able to withstand small falls and impacts.

We smooth the tape with a warm iron, this procedure will finally bake it to the foam, but for the first model this is not necessary.

To install the elevator wing, you need to make a slot in the body and push the wing into place.

We install servos on the wing. To do this, apply and outline them with a marker, then cut them out seat. We stretch the wires and use double-sided tape to secure the servos in place. On the contrary, hogs are installed on the ailerons and connected to the servos with a rigid wire.

Every child has tried at least once to build a passenger plane out of paper. The guys tried to make the design so that it would fly further and more smoothly, but more often than not, that’s where the whole hobby ended. However, having matured, some begin to ask the question: “How to make an interesting three-dimensional model of an airplane with your own hands?” If you are one of them, then you will find answers to all your questions in this article.

Materials

To make a volumetric passenger plane from paper, you need to be very careful about the choice of material, as it will have a direct impact on the quality of the finished product. You will need:

Paper;
Glue;
Scissors;
Ruler;
Tweezers;
Dye;

Paper

How high-quality the aircraft model will be will directly depend on the paper chosen. It would be logical to choose the densest one, but the harder the material, the harder it bends. Therefore, if you have to make a layout with many small details, then it is better to give preference to thinner paper, but not less than 160 g/sq.m. You can, of course, do the work from cardboard, but you won’t be able to print the details on it.

Glue

How to make a durable airplane that won’t fall apart at the first whiff of wind? Right! Using high quality glue. It should not soften the paper or leave unpleasant yellow marks. It is better to choose a universal or specialized glue for modeling. This will last a long time and will help maintain the original appearance of the paper airplane for a long time.

Scissors

Well-chosen scissors will add neatness and elegance to a paper airplane model. Firstly, they must be sharp and not damage the paper. Secondly, modeling is a rather long and labor-intensive process, so it is better to give preference to convenient models. And, thirdly, for parts of different sizes you will need different scissors, so it would be nice to have at least 3 types in your arsenal.

Ruler

Almost any ruler is suitable for building an aircraft model. The main thing is that it is rigid, because the fold lines may turn out crooked, and then it will simply not be possible to create a beautiful paper model of the aircraft.

Tweezers

This tool will be needed for gluing small parts. You can use ordinary cosmetic tweezers, but it is worth noting: the longer and sharper it is, the easier it will be to work.

Dye

Some parts have to be printed, while others, on the contrary, require working with paint. Before painting, paper requires mandatory treatment in the form of varnish, primer, putty and sanding, after which you can use anything to add color. However, if your budget allows, it is better to stick to professional modeling paints, such as Tamiya or Humbrol.

Knife

Sometimes the design contains such small details that even the smallest scissors will not work for cutting. This is where a paper knife comes to the rescue. The main thing is to choose a model with a thin, sharp blade.

Airplane assembly

Having correctly selected all the necessary tools, you can begin to make a passenger plane out of paper. If you already have extensive modeling experience, you can make the drawings yourself. For those who are gluing airplanes for the first time, it is better to go to the website https://izobretaika.in.ua, where a wide variety of schemes and templates of interesting models are offered. So, how to make a beautiful and voluminous model?

We print the stencil on a prepared sheet of thick paper;
Carefully cut out each piece with scissors (for smaller ones, use a knife);
After all the parts are cut out, use a ruler to mark the fold lines;
Next, glue all the parts together. You need to start with the main body of the aircraft;
Attach the tail and wings to the “body” of the structure;
Add smaller details such as the landing gear, windows and doors;
The paper passenger plane is ready.

Airplane painting

If you decide to resort to simple schemes and paint the plane yourself, so that the color goes on evenly and lasts a long time, It is very important to follow these steps:

The paper must be impregnated with solvent-based varnish;
Next, primer is applied (for convenience, you can use a spray);
The resulting layer of soil needs to be sanded (sandpaper is perfect);
After this, the structure is puttied, thereby removing unevenness and smoothing the surface;
Pay attention to small parts; it is better to additionally treat them with super glue for additional strength;
Apply paint to the evenly puttied model;
Let the plane dry. And everything is ready!

The work area should be well lit so that you can see every detail clearly. Scissors or a knife must be selected in accordance with the size of the elements: for large ones, large ones with straight blades are suitable, and for small ones, manicure scissors or a knife. It is recommended to cut out each spare part as needed in order to avoid confusion and not lose anything. To keep the details neat, twist the sheet of paper, but never bend your arms.

Folds

Leaning the ruler against the fold, run something blunt along it. This way you guarantee yourself neat lines while assembling the model. If you need to highlight sharp edges, it is recommended to use a knife, but only apply light pressure. This way the corners will come out clear and even.

Decide which fold you need: external or internal. To perform the first, you need to achieve a certain convexity of the part by bending it so that one of the sides is higher than the other. And in order to get the second one, then, accordingly, on the contrary, you need to make sure that you get something like a hole.

Gluing parts

This stage should be given special attention, since the appearance, quality and durability of the model will directly depend on it. Many models have tabs designed for gluing, so you need to apply glue to them and press them together. It is very important not to overdo it; if you pour too much of the substance, it can damage the structure of the aircraft, thereby making it less presentable. Squeeze out a small drop and spread it over the rest of the surface. If you need to place one spare part into another, apply glue to the sides.

Bending round parts

Sometimes a passenger airplane made of paper may have a rounded “body”. To make it look natural, it is very important to round the details correctly. To do this, place the element in your palm and run something like a pencil or pen along the inside; for smaller details, you can safely use toothpicks. This way you will achieve the desired shape and easily glue the spare part in the form you need.

Joining parts

The edges of some cylindrical elements, such as an airplane frame, can sometimes be difficult to glue together. To do this, it is recommended to leave additional space on one side without a pattern, which will “hide” under the other. This way the surface will have a perfectly smooth appearance. Glue can be applied to one edge or to both, the main thing is in moderation.

Since making a passenger plane with your own hands is far from easy, those who managed to build it can certainly be proud of themselves. Aviation is a rather complex section of modeling, since products require special attention, time, concentration and painstaking work. By following simple recommendations and approaching the matter wisely, anyone can get a beautiful, neat layout.

There is probably no boy who would not like to fly. You can fly in any way, for example, on a homemade radio-controlled model aircraft or on a paraglider.

But, you can start with a simple free-flying airplane model.

You can make such a simple aircraft model from ceiling tiles. You can paste paper printouts with a view of the airplane onto the model parts, or you can paint the airplane model yourself.

How to make a flying model airplane with your own hands

(clickable)

To make it, you will need ceiling tiles (take ones without an embossed pattern) or cardboard.

The easiest way to start making a flying model airplane is from the wing. It has a simple shape and is easy to cut. Cutting is done using a regular stationery knife. You can glue the printed templates onto the ceiling tiles in advance and then cut out the parts of the flying airplane model directly through the paper.

The fuselage is also cut from the ceiling. The wing consoles are glued at an angle of 7-10 degrees, then the aircraft model will self-stabilize in flight.

The front pads on the fuselage are needed to make the nose heavier; you may need to add weight to the nose of the aircraft model for smooth flight.

See how to properly set up your model airplane flight.

How to launch a model airplane
After the aircraft model is assembled, the question usually asked is how to properly configure the flight of the aircraft model.

Look at the picture above - if a homemade airplane model takes off after being thrown, then you need to add weight to the nose of the airplane model. This can be plasticine or a lead weight taken at a car wheel balancing station.

If the aircraft model dives, then on the contrary, reduce the weight or add it to the tail of the homemade aircraft model.

A properly configured homemade aircraft model flies smoothly.

It is best to launch a free-flying model aircraft from an elevated position, for example from the balcony of a multi-story building. A steep slope is also good for launching, the main thing is that the wind on the slope is uphill.

Watch a video of making a free-flying model from ceiling tiles.

Also interesting articles:

Do-it-yourself aircraft model - making a radio-controlled model airplane

How to make a radio-controlled yacht with your own hands - we make a yacht with radio control.

Which boy doesn't admire structures like airplanes? Do-it-yourself aircraft models made from ceiling tiles are an excellent gift for children who are interested in aviation. Especially if they took part in assembling the airframe. The article will tell you how to make a simple airplane model from ceiling tiles.

Aircraft modeling

Model airplane construction is a popular technical sport that is of interest to schoolchildren, students, workers and engineers. At the same time, everyone chooses for themselves a class of aircraft models that suits their interests.

In aircraft modeling there are three fairly large groups of aircraft models, presented in the table:

Model class	Peculiarities
	In such models, designer intervention is impossible during flight. All adjustments and settings of the aircraft are completed when it is launched. They can be: - motorless - gliders; - with a simple, very small, internal combustion engine, which is attached to the body with an elastic band. The motors on the models work for a few seconds to throw the light-winged structures up to a hundred meters up, and then they smoothly go down. Timers or special clock mechanisms are used to turn off the engine and switch the steering wheel to planning.
	With such models, the athlete controls wire threads, which are called cord. The devices fly in a circle with a diameter of approximately 40 meters. The “pilot” is located in its center with the control stick. When you pull the handle towards yourself, the elevator deflects, and the device obediently flies up. And moving the handle away from you causes the model to descend. The devices are: Aerobatics, capable of performing all aerobatic maneuvers. High-speed ones, reaching speeds of up to 300 km per hour. Racing, combining efficiency, reliability of engine starting, ease of maintenance and high quality in flight.
	Controlled remotely, wirelessly. For this purpose, there is a set of radio equipment, which includes a transmitter, in the hands of the operator, and a receiver with steering control mechanisms, mounted on board the model.

Model aircraft structure

Tip: Before you make an airplane from ceiling tiles, you need to become familiar with its design.

The design of all models is very similar. Main nodes radio controlled model aircraft are shown in the photo.

This:

Fuselage. This is the basis of the entire model on which the following are mounted:

bearing structures;
tail section;
chassis.

Installed inside:

engine;
aircraft control equipment: receiver, steering controls, batteries.

Wing. Serves to create lifting force. The wing keeps the model in the air.
Ailerons- control surfaces located at the rear end of the wing and deflected up or down in antiphase. They allow the plane to tilt left and right.
Tail. It consists of a vertical part - the keel, and a horizontal part - the stabilizer. This device provides stability to the aircraft so that it can fly straight and level without tumbling in the sky, randomly changing the direction of its movement.

The rudder is installed at the rear end of the keel.

Chassis. Allow the model to take off from the surface and then land on it.

Advice: If there is no landing gear, the model should be launched by hand, and the plane should be landed “on its belly”.

Engine. Creates the movement of the model, allows it to gain the desired height, and then maintain a given speed.
Tank. Serves for the fuel needed to run the engine.

Receiver. Receives the transmitter signal, amplifies it, and processes it. And then it transmits to the steering gears.
Steering cars. The signal coming from the receiver is converted into moving the model's rudders through the connected rods.
The receiver and machine are powered from the on-board battery. Usually these are four “finger” elements.

Model selection

Advice: When choosing to make an airplane from ceiling tiles with your own hands, you need to ensure, first of all, that it is reliable to take off and land, and then that it satisfies aesthetic needs.

The aircraft model must have the following properties:

Be stable: stay in the air well without much input from the pilot.
It is easy to repair, which is ensured by aircraft models made from ceiling tiles.
Sufficient strength, but without compromising flight qualities: withstand hard landings and fly well.

We do it ourselves

To work you will need tools and materials:

Making any design, including an aircraft model, with your own hands begins with the development of drawings. To do this, you can use the services of specialists or copy them from websites, print templates on a printer or draw them according to size.

After the printer:

Printouts on A4 sheet formats are laid out on a flat surface according to serial numbers. The result should be a life-size image of the aircraft elements.
All the necessary sheets are glued together.
When gluing sheets without disturbing the dimensions and geometry of the future aircraft.
Cutting lines are drawn by connecting special crosses drawn at the corners that define the boundaries of the image.
The resulting airplane drawings from ceiling tiles are combined with structural fragments, glue is applied to the uncut edges of the sheets, and all parts are carefully glued together so that their joints coincide very precisely.

This way all the fragmented elements of the model are glued together.
Paper templates are cut out with scissors.

Manufacturing of blanks

Blanks for assembling the aircraft are cut from ceiling tiles using prepared templates.

Tip: To prevent the sheets from moving from the tiles, they must be fixed to the surface of the material with glue. After marking is completed, the glue does not have time to dry and the paper is easily removed without damage for further use.

To mark a simple part with straight lines, it is enough to pierce all its corners with a needle.
Remove the stencil and, using a ruler from adjacent puncture points on the tile, cut through the material with the tip of a knife.
The ruler is shifted to the next adjacent points until the complete cutting of the part is completed.
A workpiece of complex shape with rounded sides can be completely cut out according to the template.

It is advisable to mark each part to facilitate its purpose, according to the assembly drawing.

Airplane assembly

Before you start assembling all the parts, it is better to watch the video.

The aircraft assembly technology can be roughly described as follows:

Double partitions consisting of several parts are glued together, which increases their strength. For example, fuselage partitions.

Tip: For work you should use Titan glue, its price is the most affordable for beginning modelers. It is more convenient to apply glue with a syringe without a needle, using it as a dispenser.

To ensure that the ends of the cut parts are smooth, they are sanded with sandpaper.
The side of the fuselage is placed on the table so that the front side is towards the outside of the aircraft. All mounting holes are cut out on it.
Using this part, the same holes are made on the second half of the fuselage.
Glue is applied to the glued side of the front compartment partition blank and the part is pressed into place at the installation site. After spreading the composition on the mating part, the workpieces are separated and left for the glue to partially dry for about 30 seconds. The parts are connected again and pressed with force for about 10 seconds.
When assembling an aircraft, it is necessary, if necessary, to adjust the dimensions of the battery compartment, constantly checking with a square or ruler the perpendicularity of the parts being joined.
This is how all the fuselage partitions are gradually assembled.

After installing all the partitions, the second side of the fuselage is glued.
The nose of the aircraft and the mounting of the frame for the engine are being completed.
The upper part of the fuselage is installed.
The tail blanks are glued together. In this case, reinforcement is immediately laid down from reinforced tape to fix the rudder and toothpicks for rigidity.

The gluing is clamped with a board and clamps, which will ensure evenness of gluing.
The tail is glued into place.
The verticality of the elements is controlled and strictly maintained.
The elevator parts are glued together. In this case, a bamboo skewer and tape are placed inside to fix the steering wheel. To ensure reliable gluing of the ceiling halves, the tape can be perforated with holes.
The elements are compressed with a board and clamps, and left for about a day until the glue dries completely.
The edges are ground down with sandpaper or a stone at an angle of 45°, which will allow them to not rest against each other when the planes of the model are tilted.
The wing is assembled, lines are marked on it for gluing stiffeners, ribs, and spars.

A wooden axle or spar can be made from a wooden ruler 50 centimeters long.
The spar rail is glued.
The joint in the center is reinforced with two small slats.
Foam plastic neurites are glued in.
The desired shape of the wing plane is set. To do this, the substrate or ceiling material is rolled onto a piece of pipe.
Glue is applied to all mating elements and final gluing is performed. While the adhesive composition is setting, the wing is fixed in any available way: weights, clothespins, tape.

Small dents caused by clothespins are sanded with sandpaper.
The cavities in the center of the wing are closed and inserts are glued.
After the glue has dried, the ailerons are marked. In this case, it is necessary to additionally look at the assembly in the light so as not to get on the partition.
They are cut through on both sides with a cutter, and the finished aileron is removed.
Opened cavities are sealed with strips of tiles.
The ailerons can be glued immediately with reinforced tape or later, before the main fitting of the aircraft model.
The front part of the wing can be reinforced with reinforced tape.
The entire model is covered with tape, which serves for beauty, and most importantly gives the structure greater strength, which will allow the product to withstand impacts from falling.
The adhesive tape is smoothed with a warm iron, which will finally attach it to the ceiling tiles.
A slot is made in the body of the aircraft into which the wing is installed.
Servos are installed on the wing. To do this, the elements are applied and outlined with a marker, and a seat is cut out.
The wires are pulled with a homemade wire hook.
On the contrary, hogs are installed on the ailerons and connected to the servos with a rigid wire.
Two servos are installed in the aircraft fuselage, for the rudder and the elevator.
For fixation, it is better to use double-sided tape, glued to all contact areas of the servo.
The elements are installed in place and the supporting walls are additionally glued. The rods are laid from rigid wire to the rudders.
A frame is made to mount the motor.
Thin plywood is glued to the motor mounting side; bolts will be screwed into it for fixation.
The frame for the motor is glued into place.
The motor driver is mounted at the front of the fuselage, and the wires are brought out through the ventilation window and connected.

Car modeling, motor glider, foam planes. Motor installation

The direction of rotation is checked.
The fairing is put in place and secured with tape.
To strengthen the installation site of the wing, it must be secured by gluing plywood or thin shingles.
The receiver is installed, and all the wires from all the electronics are collected together.
The bottom of the fuselage is glued, a hatch is cut for mounting the battery.
The total weight of the model is approximately 450 grams.
You can fly over a model airplane. The video will show you how to do this.

Assembling airplanes from ceiling tiles is the simplest option, which a novice aviation enthusiast can do if desired. The main condition is to do everything carefully, adhering to the assembly technology, and it is better to take the advice of a specialist.

Here's what we did (video)

Probably every adult in our country knows how to make a paper airplane. After all, this simple toy, originally from childhood, invariably delights and amazes with its ability to fly. Before the dominance of tablets and other gadgets, it was ordinary paper airplanes that delighted boys of all ages during recess.

How many schemes for assembling this toy do you know? Did you know that from an ordinary sheet of A4 paper, you can fold many different types of aircraft, including long- and far-flying ones, as well as military models?

Are you already intrigued? You can start folding airplanes right now. After all, all you need for this is paper, desire, a little patience and our diagrams. Let's fly!

The simplest diagrams of a basic aircraft model

Before moving on to complex models, let's brush up on the basics of aircraft construction. We present to your attention 2 of the most simple ways fold the airplane.

Using the first scheme, it is easy to get a universal airplane familiar from childhood. It does not have any special takeoff and landing characteristics, but folding it is not difficult even for a child. An adult can complete the assembly in just a minute.

If even the first scheme seemed too complicated to you, use the simplified method. It allows you to get the desired result as quickly as possible.

He's in the video:

An airplane that flies for a long time

Every child’s dream is a long-flying airplane. And now we will help you make it a reality. Using the diagram provided, you can fold a model that differs in flight duration.

Remember that flight performance is affected by the size of your aircraft.

Excess weight, which means the length of the wings, prevents the plane from flying. That is, a glider must have short, wide wings. Another friend of planning is the absolute symmetry of the model.

You need to throw it not forward, but upward. In this case, it will stay in the sky for a long time, smoothly descending from a height.

Find answers to the remaining questions and all the subtleties of folding a paper glider in the step-by-step video tutorial.

Circuits that provide fast flight

Do you want to take part in an aircraft model competition? They are easy to arrange at home. Just make high-speed airplanes out of paper - and you can set your own records.

Step-by-step following our photo instructions is the key to success. A number of general recommendations will also help beginning paper aviation enthusiasts.

To improve flight performance, use only a completely flat sheet of paper. Ideal for regular office printers. Any bruises and folds will repeatedly worsen the aerodynamic properties of the model.
Iron all folds with a ruler to make them clearer.
Sharp nose of an airplane increases its speed, but at the same time range decreases flight.

Ready-made crafts can be painted with the children. This exciting activity will allow you to turn a folded piece of paper into a real attack aircraft or an unusual fighter.

Approach creating your models like a science experiment. The speed and ease of assembling origami airplanes allows you to analyze their flight and make the necessary changes to the design.

Be sure to check out the video master classes on how to create fast paper airplanes to avoid annoying mistakes and learn from the experience of others.

Paper long-range fighter

Describing this aircraft model, many enthusiastically promise that it will be able to fly 100 meters and call it a super-airplane. At the same time, they are not at all embarrassed that the officially registered record for the flight range of a paper airplane is only 69 m 14 cm.

However, doubts aside. In any case, such a cool handsome man is worthy of you working on his creation. For this craft, stock up on a sheet of A4 paper (you can take thick colored paper to make the airplane as beautiful as possible), unlimited patience and accuracy. If your goal is a realistic fighter, take your time assembling it and follow the photo instructions step by step.

There is also a video at your disposal from which you will learn how to properly assemble a paper fighter plane that stays in the air for a long time.

A model that features stable flight

A paper airplane takes off and immediately begins to fall, or instead of a straight trajectory it writes arcs. Does this sound familiar to you?

Even this children's toy has certain aerodynamic properties. This means that it is the duty of all beginning aircraft builders to approach the construction of a paper model with full responsibility.

We invite you to fold another cool airplane. Thanks to its blunt nose and wide deltoid wings, it will not go into a tailspin, but will delight you with a beautiful flight.

Do you want to perfectly master all the intricacies of building this glider? Check out the detailed and accessible video tutorial. After a powerful charge of inspiration, you will definitely want to fold an airplane with your own hands that will flutter like a bird.

The corn plane is an original craft for young aircraft modelers

Do you have a growing boy who already loves making things, gluing and cutting? Give him a little time - and together you can make a small model of a corn-crop airplane. It will definitely bring a lot of joy: first from joint creativity, and then from fun with a toy you made with your own hands.

For work you will need the following materials:

colored paper;
double-sided colored cardboard;
Matchbox;
scissors;
PVA glue.

The process of creating a toy is as simple as possible: forget about exact drawings and the need to first download and then print a complex template. Even under your leadership Small child will be able to build his first plane.

First of all, cover the matchbox with colored or white paper. Cut a strip of cardboard 3 cm wide. Half of its length will correspond to the length of the aircraft fuselage. Fold the strip in half and glue it to the box.

Cut out two identical rounded wings, their width should be slightly larger than the width of the box.

Glue the wings to the plane. You can entrust this to your little helper; he will be happy about such an important mission and will do everything well and thoroughly. Cut and glue a rectangle to the front to hide the box.

Cut two elongated ovals for the tail of the plane and a strip for the vertical part. It needs to be folded as shown in the photo.

Glue the blanks to the tail of the corn plant. The resulting cardboard masterpiece remains to be decorated according to your wishes. You can glue stars or small pictures to it. A propeller made from thin strips of paper would be a good addition.

Such a wonderful airplane can be taken to kindergarten as a craft or to please dad on February 23rd.

Video bonuses

Do you want to get a plane that can not only take off high, but also return back to your hands? Do you think this can't happen? But you are wrong.

Tireless experimental craftsmen have developed a design for an amazing aircraft - boomerang.

With it, you can show your friends a stunning trick: a launched airplane will obediently fall right into your hands every time. To become known as the master of paper airplanes, check out our video - you will definitely succeed.

It would seem that all the paper airplane samples have already been reviewed and tested in practice, but we still have something to surprise you with. We invite you to watch a video lesson on creating a realistic glider plane.

You don't even need origami folding skills, you just cut out the outline from paper. This model has excellent flight characteristics, and the whole secret lies in... ordinary plasticine. Watch the video, be surprised and amazed.

Creating various paper airplanes is not only a wonderful activity that allows you to drive away boredom and put away the ubiquitous gadgets. It develops intelligence, accuracy and fine motor skills. That is why it is so useful to include this type of activity in the program of joint leisure with children.

Perhaps the first unsightly model will be your child’s first step towards a serious interest in aircraft modeling. And it is in your family that a brilliant designer of passenger airliners or new jet fighters will grow up. Anything is possible. There is no point in looking too far into the future, but devoting an hour or two to folding paper airplanes is definitely worth it.

Download aircraft model drawings. Craft airplane - how to make a model airplane from wood, paper and plastic with your own hands. Equipment for launching gliders